It is fairly typical to be perplexed regarding which solder wick to buy. This difficulty occurs because to the wide variety of solder wick available on the market. To help you choose the finest solder wick available on the market, we have produced a detailed guide.
10 solder wick: Editor Recommended
Our Editor 10 solder wick Review:
1. TOWOT Solder Wick Braid With Flux No-Clean Electronic, Desoldering Wick Braid Remover.Desolder Soldering 2mm W 0.08” L 9.8′
- Quality materials：The Braided Desoldering Wicks are made of 100% copper wires with a fine braid design. Using flat stitch weaving, fast heat conduction, to promote strong capillary action to pull in excess solder.
- Easy to use: the desoldering wicks can provide an easier way to correct mistakes on small PCB boards and will not make damage to the board, clean small components, suitable for re-soldering and desoldering.
- Extensive applications: the braided solder wicks are suitable for labs, school, home, and industrial welding work; And the wicks adopt a fine braid design to promote strong capillary action, bringing more convenience to your daily work.
- Low residue design: No-Clean solder wick braid will just leave little residues after use and the residues are non-conductive and non-corrosive, no need to waste your time cleaning it.
- Warranty ：If you have any questions, please feel free to contact us at any time. Thank you!
Additional Info :
2. Lesnow solder wick braid with flux Super 10ft Length Desoldering Wick Braid Remover Tool Solder Sucker 1 piece No-Clean soldering Wick Wire Roll and Disassemble Electrical Components
- 🌟The solder wicks can be used to correct mistakes with small boards on PCBs, remove relays and other components from printed circuit boards, re-solder mechanical keyboard switches, unsoldering old wire from devices, desoldering computer parts such as a motherboard,clean alloy on smd components and more
- 🌟1 pieces of no-clean solder wicks, each wick is about 10ft long and 0.1 inch in width, enough quantity and length for your daily needs
- 🌟This desoldering wick has geometrically-precise weave with copper and rosin, work from the tip of the desoldering wick, once the desoldering wick and the solder has been heated, the solder braid can quickly absorbed molten solder and left a clean working area.
- 🌟The desoldering wicks are made of copper wires with nice quality, precise weaving design can improve the capillary effect and the redundant solder absorbing ability, increasing your efficiency
- 🌟The braided solder wicks are suitable for labs, home and industry welding work, practical tools to remove solder and correct errors on small PCB boards, bringing lots of convenience for your work
Additional Info :
3. MG Chemicals 426 Desoldering Braid #4 Fine Braid Super Wick with RMA Flux, 5′ Length x 0.1″ Width, Blue
- Oxide-free clean copper
- Static free bobbins
- Only pure type ‘RMA’ rosin is used meeting the requirements of MIL-F-14256F (ANSI/J-STD-0004)
- Manufactured under SPC guidelines
- Designed to leave a residue that is environmentally safe
Additional Info :
4. NTE Electronics SW02-10 No-Clean Solder Wick, 4 Blue.098″ Width, 10′ Length
- Removes up to four times more solder than conventional wick, and extracts solder much faster than wicks based on Type-R fluxes
- Residue left behind is halide free and non-conductive, so it does not have to be cleaned off the board
- 100% copper wick has fine braid design to promote strong capillary action to pull in excess solder
- Available with standard or anti-static bobbins
Additional Info :
5. AUSTOR Desoldering Sucker and 6 Pcs Solder Braid Wick (2.0mm/2.5mm/3.0mm Width, 1.5m Length) with Flux – Desoldering Vacuum Pump Solder Removal Tool
- High efficiency solder sucker – the desoldering pump designed with double ring and “vacuum” open button, you can remove solder from circuit board effectively by cocking it and pressing the trigger button with one hand
- Desoldering braid wick with rosin – 6 pieces copper solder braid in 3 size, width 2.0mm/2.5mm/3.0mm, length 1.5m, 2 pieces for each size; geometrically-precise weave, can be used to clean the spare solder on the pin away to avoid short circuit, to meet your various of soldering needs
- High quality material – the desoldering pump body made of premium quality ABS material, with non-slip sponge and nylon nozzle, anti-static, heat resistant and durable
- Wide application – correcting mistakes on small PCB boards, removing relays and other components from printed circuit boards, cleaning small components, re-soldering and desoldering
- 7-in-1 solder removal tool – 1pcs solder sucker and 6pcs solder wicks in 3 size
Additional Info :
6. GOOT Solder Wicks Made In Japan No-Clean Solder Braided Wicks Desoldering Wicks With RMA Flux,59’Length x 0.12″Width
- Brand History — Founding in 1965, GOOT had captured a 60 per cent share of Japan’s domestic market for soldering products and for almost 50 years has been providing customers with a wide range of high quality and easy-to-use soldering products.
- High Efficiency — High performance solder absorbing wire precision preparation with copper wire and special chemical formula, suitable for precision instruments (RMA corresponds to the use of standard flux). Our thin and soft desoldering wire’s flat braid has efficient thermal transmission. Removes solder faster with better heat response than previous wicks. Recommended for lead-free solder with high heating load.
- Good Quality — Solder wire with flat needle type preparation, soft design, fast heat transfer, suitable for fast absorption. It not only help you improve efficiency and quality, also more environmentally friendly.
- Safety and Variety — Use at ease. No fluorine, low residue, suitable for a variety of PCB circuit boards. Size – W 0.12″ L 59″
- 100% Satisfaction Guarantee — You can return the undamaged product and packaging without any reason within 30 days. Any problems can be contacted by email.
7. Tabiger Solder Wick & Desoldering Pump, Solder Sucker & Desoldering Wick, 2pcs Solder Braid (2.5mm Width, 1.5m Length)- Desoldering Vacuum Pump Solder Remover
- 【One-handed solder sucker with powerful suction 】 Whether you are right or left-handed, you can using the desoldering pump by just cocking it and pressing the trigger button with one hand when you are ready, the desoldering pump designed with double ring double open and “vacuum” button, which make the sucking power awesome.
- 【Desoldering Wick with copper braid】 2pcs solder braid with the size 2.5mm Width, 1.5m Length, this desoldering wick has geometrically-precise weave with copper and rosin, work from the tip of the desoldering wick, once the desoldering wick and the solder has been heated, the solder braid can quickly absorbed molten solder and left a clean working area.
- 【ABS body with non-slip sponge and Nylon nozzle desoldering pump】 The body of the desoldering vacuum pump is made of high quality ABS, which make the solder sucker delicate and durable, also the covered sponge can absorb sweat and heat, make it comfortable to hold, the nylon nozzle of the solder suck can endure high temperature, thus it can be used for a long time.
- 【3-in-1 Solder Removal Tool】 1pcs desoldering vacuum pumps and 2pcs solder wicks, a must-have tool for electronics kit, the desoldering wick absorbs solder, the desoldering pump pulls it away quick, while the solder wick is better for small amounts of solder, the solder sucker takes up large amounts.
- 【Widely used Solder Remover】 The Desoldering Wick & Desoldering Pump can be used to correct mistakes with small boards on PCBs, remove relays and other components from printed circuit boards, re-solder mechanical keyboard switches, unsoldering old wire from devices, desoldering computer parts such as a motherboard,clean alloy on smd components and more.
Additional Info :
8. No Clean Soldering Flux Pen and Solder Remover Wick, 0.1 Inch Wide and 59 Inch Long, Solder Braid Wick Liquid Solder Flux Pen for Electronics Welding Repair Tabbing Wire Maintenance (6 Pieces)
- Package includes: you will receive 3 pieces of no clean solder flux pens, and 3 pieces of soldering braided wick, in total of 6 pieces, sufficient quantity and a considerate combination to meet your needs for daily use and replacement
- Suitable size: the rosin flux pen measures about 14.3 cm/ 5.6 inches in length, and the solder braided wick is about 1.5 m/ 59 inches long and 2.5 mm/ 0.1 inches wide, which is convenient to hold in hand; Please check the size carefully before purchasing
- Quality material: these no-clean soldering wicks are made of quality copper wire and adopt precise weaving technology, which can enhance tension on the surface to absorb excess solder; The liquid solder pen is made of reliable materials, no leaking and safe for protecting the flux, preventing you from touching the organic solvents
- Practical tools: 10-ml solder flux pen with soft brush tip can release the liquid flow moderately, which can clean the components without harming the PCB board copper foil or IC pin; The solder remover wick features good thermal conductivity and absorption, useful to reduce the risk of thermal injury to the circuit boards
- Wide applications: these flux pens and braided solder wicks can be applied for laboratory, computer, home repairs and correcting small PCB board errors and through-hole solder joints, electronics welding, etc., bringing a lot of convenience to your work and improving efficiency
9. Solder Sucker Desoldering Wick Kit，Solder Wick & Desoldering Pump,Sucker & Solder Wick(2.5mm Width, 1.5m Length) Vacuum Pump Solder Removal Tool
- Convenient Design:The solder sucker with concise construction, so whether you are right or left-handed, you can using the desoldering pump by just cocking it and pressing the trigger button with one hand when you are ready.
- Desoldering Wick： Each wick is about 2.5 mm/ 0.1 inch in width and 1.5 m/ 5 feet long .It could help clean the spare solder on the pin away to avoid short circuit, especially in small, hard to reach areas.
- High-quality Solder Sucker:The pump body for desoldering is made of aluminum, which can resist impact, corrosion and has good heat dissipation. The suction wire for desoldering has a precise geometric braid of copper and rosin, and there will be no cuts after a period of time or bend.
- Easy to Use:It is very convenient to use, it can well remove the existing solder from the circuit board. Quickly remove the residue, heat the solder and press the button and solder slag, all the solder is sucked away, super easy to desolder.
- Perfect Solder Removal Tool: The solder sucker can be used for broad place, which the solder wick can be used for small, hard to reach areas, all together can be used to correct mistakes with small boards on PCBs, remove relays and other components from printed circuit boards.
10. CHEMTRONICS 80-3-5 BRAID, DESOLDERING, ROSIN SD, 5FT
- Price For: Each Braid Material: Copper Width: 2mm Length: 5ft Braid Color: Green Braid Size: #3 Features: Packaged in ESD-Safe Static-Dissipative Bobbin Flux Type: Rosin Activated RA Leaded Process Compatible: Yes RoHS Compliant: Yes
- Country of Origin:United States
- Package dimensions:15.24″L x 7.62″W x 0.51″H
- Package weight:0.8 lb
Additional Info :
Important Aspects to Consider When Choosing solder wick:
How we Picked the Top solder wick
Most of the items mentioned are not hand-picked. The list was generated by AI. But we can guarantee that every product included here has been tried and tested by real people, reviewed by experts, and recommended by real people.
Cost and performance are essential factors to consider when acquiring a solder wick. More enterprises entering the solder wick market means more options for quality and performance. The most expensive solder wick does not always indicate the best decision for you and your money. Many low-cost models offer excellent performance and comfort.
A brand with high-quality products and outstanding customer service is the ideal choice for solder wick. Good brand products are created with extreme care and precision, and they will always be available to answer your questions, correct any product flaws, or refund your money if any damage is found.
Before you click the buy now button or add items to your shopping cart, make sure the product fulfills your requirements.
Specs matter while choosing a product. They define the product’s capabilities. With so many options available, it’s vital to pick the correct one.
Choose the solder wick precision-engineered to fit your demands.
Performance, features, and affordability are the three primary factors to consider when comparing specifications. Each of these criteria has a role in your final choice. Considering all of them ensures you got the most value for money.
The world is filled of great solder wick, making it difficult to choose. A decision can be made by looking at the design. Materials used in manufacture, color scheme, and even visual weighing all contribute to a product’s overall design. Knowing this can help you locate a product that exactly meets your tastes and demands.
Many individuals consider customer reviews while making purchase selections. It’s easy to see why: who knows a product better than those who have used it? When deciding which product to buy, looking through customer reviews can give you a good indication of how others felt about their experience. Not everyone will enjoy every product, and some people will be more likely to post a review than others. Overall, customer evaluations are a good reflection of how happy people are with a product.
Stability and Control
We weighed the stability and control of a solder wick in determining its performance.
Keep in mind the item’s stability and control.
We consider the product’s impact on our lives and how we will feel when utilizing it.
Nobody likes to be uncomfortable or constrained when doing what they love. When deciding whether to use a product, consider its comfort solder wick. There are various sorts of solder wick that provide stability, control, and comfort. If you buy a fishing kayak, you don’t want to spend the whole trip thinking about how badly you want to get out because your back hurts or your feet are tired.
The manner a solder wick is designed and built, as well as the material used, determine its durability. Select the solder wick that can tolerate wear, pressure, and damage.
Also, make sure it has a streamlined style that fits everywhere. A busy mom or a construction worker will appreciate this product’s durability.
What Are Today’s Most Popular solder wick Models?
There are many solder wick items accessible today for men and women seeking quality and reliability. Every solder wick model follows the same essential premise. But they appeal to various users.
It’s no secret that certain products appeal to specific populations. What if you could see which products were the most popular across all consumers? You can, and we’ve got the list. Check out our collection of products that appear to appeal to all ages, genders, and locations.
How to Choose the Most Popular solder wick
The three most crucial criteria to consider are price, quality, and popularity.
Price is an obvious factor to consider, as you want to ensure it is acceptable for your needs.
Quality should also be examined because buying a low-quality goods will not help you achieve your main aim of obtaining the best product.
Finally, while not as obvious as price or quality, popularity can be just as significant as both when it comes to attracting new customers.
1: How much is solder wick?
solder wick come in a variety of designs and pricing ranges. It’s difficult to predict product costs nowadays. You don’t know how much something costs because the pricing range is so vast. For example, a pair of pants can range from $20 to $200 depending on where you buy them. Similarly, additional goods like as solder wick.
2. Is solder wick worth it?
We are, without a doubt, a disposable civilization. We’re continually assaulted with ads advertising the latest and greatest solder wick. But are they solder wick worth our money? Some of them are if you pick wisely! Some, not so much.
3. Is it time to get a new solder wick
You’re looking for a new solder wick. What do you think? It’s difficult to predict future price changes. If there are no signs of production slowing, it can be worth buying now to enjoy your investment sooner. But if output is declining and prices are predicted to rise, you might want to wait until the buzz has died down before making a choice.
4. What is the solder wick?
Sorry if you’re perplexed. I know it’s not an easy choice! But it’s one of the most crucial choices you’ll ever make. If you’re still unsure which type of solder wick is best for you, I recommend comparing the characteristics and functionalities of the solder wick listed above. Each has advantages and disadvantages.
5. Why should I buy a solder wick?
You can tell if you need or want a solder wick by looking at your existing inventory. You probably don’t need it and should reconsider buying it. If you can’t get go of the old one, you could sell it and use the proceeds to buy the new one.
This is a fun and easy approach to finish your task.
Let’s face it, we all want to feel good about our purchases. But there are so many! How can you know which is best? You need not be concerned because Follies Broadway has your back. Our trained staff is here to help you find what works for you. Before making a final decision, you can take advantage of our free consultations.